Product Search

・Flaw detection sensitivity is pursuant to JIS and ASTM
・Not applicable of Japanese Specific Chemical Substances Obstacle Prevention Regulations
・Not applicable of Japanese Organic Solvent Toxicity Prevention Regulation (U series)
・Beneficial for enhancing working safety and health and improvement of working environment
　(Not applicable of Japanese Industrial Safety and Health Law)

・Not applicable of Japanese Specific Chemical Substances Obstacle Prevention Regulations and
　Japanese Water Pollution Control Law
・Not applicable of Japanese Organic Solvent Toxicity Prevention Regulation and PRTR
・Aerosol cap is spray-through cap (E-T series)
・Conformity with JIS-Z-2343-2 and ISO-3452-2 (E-ST, E-T series)
・Easy drainage treatment and COD value can be decreased more than 97% by coagulation method

・High-brightness fluorescent penetrant for precision inspection
・Not corrosive to all kinds of metals

・High-brightness fluorescent penetrant for precision inspection
・Not corrosive to all kinds of metals

Eco-Glo EG-2000 (Water washable Fluorescent Penetrant)
・Easy waste water treatment. COD value can remarkably be decreased
・Excellent water washability. Washing time and amount of washing water can be reduced
・Less over-washing
・Conformity with RoHS/ELV
・Environmental friendly. Eco-Glo is made from natural materials
・Not applicable of Japanese Organic Solvent Toxicity Prevention Regulation and PRTR

・Efficient inspection of large quantity of parts with a few inspectors
・Unit can be selected from 3 types of standard model in accordance with the size of the
　workpiece to be inspected
・Custom design unit is available

・No drainage treatment facility is necessary. Special solvent remover is used for washing and
　reused after recovery
・Remarkable improvement of inspection capacity because of no drying process
・Post cleaning process is not needed
・Not applicable of Japanese Fire Prevention Law

・High fluorescent brightness enables detection of tiny flaws easily.
・Since separation and degradation of the fluorescent material is low, it can be used for a long time.
・Since a small amount of agent can test a large quantity of specimen, testing cost is reduced.
・Lineup which meet AMS3044.

・Highly sensitive fluorescent magnetic particles ensure clear indication of flaws.
・The density of the magnetic particle solution has been optimized in advance.
・The airtight container means the magnetic particle density will not change.

・Products which meet AMS3044 and SAE AS4792 standards.
・Since two-layer separation hardly occurs and storage stability is good, it can be used immediately after lightly shaking the container.
・Since dispersion stability is good and density fluctuation of the magnetic particle solution is small, only a smaller quantity is needed.
・Since the wettability is good and the magnetic particle solution can be uniformly dispersed, inspection accuracy is improved.
・Because the single liquid concentration type contains the dispersant, test conditions are consistent and stock control is simplified.

・Fully automatic, in-line continuous inspection using CCD cameras and image processing unit,
　complete control from operation room thus no worker in the inspection area
・Detecting longitudinal, transverse and corner defects simultaneously
・Fast inspection speed, max. 40 m/min.
・Outputting Map-data of flaw positions for each divided section of the billet surface,
　size of which is 100 mm (longitudinal) x 20 mm (circumferential)

・In-line continuous inspection during the billet being transferred
・Low equipment cost, less installation space
・Flaw inspection can be done by two inspectors.
　This is less than one half compared to required number of inspector of Axial electric current
　magnetization method
・Detecting longitudinal, transverse and corner defects simultaneously

・Excellent detecting accuracy is realized due to improvement of S/N by the effect of magnetic
　saturation device
・Fast inspection
・Marking control number or NG mark on the pipe (Option)
・In-line automatic ECT system to fit existing production line can be designed

・Using MARKTEC original theta probe, accurate inspection with large lift-off
・Fast inspection (during pipe turning at peripheral speed 60 m/min.)
・Paint shot NG marking on the pipe (Option)
・In-line automatic ECT system to fit existing production line can be designed

・Detecting probe does not contact with workpiece, therefore does not wear
・All directional flaw inspection can be done by one probe
・Paint shot NG marking on the pipe (Option)
・In-line automatic ECT system to fit existing production line can be designed

Mobility
・Compact&Lightweight:Approx.500g

Longer operating life
・Lamp life is approx.10,000 hours(20times of former product.)

High function
・High intensity:4,050μw/cm²(Gap 381mm/15 inches)

・A Cableless & lightweight design allows operators to have a long-time operation with less fatigue
・LED light source, packing, battery cover, etc. can be easily replaced by the customer
・Original design to prevent water intrusion and filter cracking

・LED light source life accomplishes approx. 10,000 hours.
　(Conventional metal halide light source is approx. 1,500 hours)
・100W power consumption is less than 1/3 comparing with conventional type.
・Under the irradiation coverage of 600×250mm, UV intensity is more than 3,600μW/cm².
・Safe LED light source with less heat.
・Simply replacement of LED light source.

・LED light source life accomplishes approx. 10,000 hours.
　(Conventional metal halide light source is approx. 1,500 hours)
・70W power consumption is less than 1/6 comparing with conventional type.
・Central UV intensity is more than 6,300μW/cm².
・Safe LED light source with less heat.
・Simply replacement of LED light source.

・Illuminates over a wide horizontal area.
　Perfect for testing long materials and shaft products.

・Employs a unique lens structure utilizing three UV-LEDs.
　Reduces running costs compared to existing products.

・Includes a UV light-dimming function.
　UV strength can beadjusted to match the conditions of individual testing areas.

High Intensity UV Radiation
・You never need a darkroom any longer as you can inspect under visible light of 100 Lux.
　The metal halide lamp emits near UV radiation efficiently and offers twice as strong as
　Black-Light of mercury type in the same electric power.

Compact body
・Maintenance and installation is easy. And the body being cooled down constantly with
　the exhaust fan, the temperature of outside of the body is kept at around 35°C
　(room temperature : 20°C).

Having the advantages of extra high UV intensity with center concentration.

Halation cut filter
・New UV transmission filter eliminates the obstacle visible light (Red and Purple) for
　observation (type-2 filter).

・Fluorescent penetrant testing is possible carried out even under (brightness of the plant in
　general) a bright environment of 100-200 lux (4000μW/cm² in case of 100 lux, 5000μW/cm² in
　case of 150 lux,6000μW/cm2 in case of 200 lux)

・By light control function, it offers an intensity of 5000μW/cm²
　and keeps it for about 3000 hours at 800mm off the filter.

• The Digital UV Intensity Tester can measure UV irradiance up to 15,000 μW/cm²
in digital numbers.
(The Digital UV Intensity Tester can display measurement values up to 30,000 μW/cm²)

• Since the size of UV light sensor is minimized, UV light distribution can be measured accurately.

• Ultraviolet irradiance is displayed as an absolute value (display: x10 μW/cm²)

• The measurement reading is accurate as the UV light sensor accepts the light with
the wavelength of 360 ±20nm without being affected by other light such as visible light.

• The Digital UV Intensity Tester satisfies the response characteristics of
the JIS Z 2323 requirements.

Leak-Checker is used for leak inspection of hydraulic equipment, large pressure vessel, transmission case etc.
MARKTEC offers checker for oil leak, water leak and air leak.

・Correlation with Shore hardness is very high.
・Conversion to every hardness scale is possible. (HS, HRC, HV, HB)
・Speedy measuere without personal error.
・Memory function is equipped, can transfer data by Bluetooth or USB.
・Usable by AA bttery 2 pcs.
・Select from various language and can use worldwide.

・Distinct dot-matrix marking with special paint
・High speed marking (Max. 207 m/min.)
・Easy and stabilized start-up even after one week holiday
・Low running cost because of drop-on-demand marking
・Light (approx. 2.6 kg) and small marking machine
・Fully automatic operation

・Distinct dot-matrix marking
・Failure self-diagnosis system
・Early resumption of operation
・Quick-drying of the paint of markings
・High-speed marking：120m/min

・Fully automatic marking in accordance with the marking data from host computer
・Fast response pencil guns spray clear, sharp and uniform dot marking
・34-dot-matrix dense special marks and fonts can be registered max. 999 kinds
・Extremely precise marking can be done on stationary plate

・Fully automatic marking in accordance with the marking data from host computer
・Fast response pencil guns spray clear,
　sharp and uniform dot marking at the plate transfer speed of 120 m/min.
・36-dot-matrix dense special marks and fonts can be registered max. 999 kinds
・Fast marking cycle/High productivity because of the marking during the plate is running

・Fully automatic marking in accordance with the marking data from host computer
・Extremely precise marking can be done on stationary pipe
・Fast response pencil guns spray clear, sharp and uniform dot marking
・Numerals, Alphabets, Symbols and special marks can be marked on full length of pipe
・Multi-line marking and parallel marking of several pipes can be done if multiple marking machines
　are installed

・Fully automatic marking in accordance with the marking data from host computer
・Fast marking cycle and high productivity because of the marking during the pipe is running on
　the conveyor
・Fast response pencil guns spray clear, sharp and uniform dot marking
・Numerals, Alphabets, Symbols and special marks can be marked on full length of pipe
・Multi-line marking and parallel marking of several pipes can be done if multiple marking machines
　are installed

・Fully automatic marking in accordance with the marking data from host computer
・Fast response pencil guns spray clear, sharp and uniform dot marking
・6 axes, articulated industrial robot is used for moving the marking head to follow curved surface
　of the pipe
・Max. 20 lines of characters (Numerals, Alphabets, Symbols and special marks) can be marked
　circumferential direction of inside/outside of the pipe and longitudinal direction of outside of
　the pipe

・Fully automatic stamping in accordance with the stamping data from host computer
・5 pneumatic styluses are controlled independently and ensure high speed,
　high quality stamping. Stamping 50 characters in 11.5 seconds
・Numerals, alphabets, symbols and special marks can be stamped
・Stamping both longitudinal direction and transverse direction of plate by rotating the stamping
　head

・Rapid response marking
・Marking on wet surface and oily surface is possible
・No nozzle clogging
・Approx. 15 mm diameter one point marking
・Paint shortage alarm is equipped
・Air-driven pumps for paint and lubricant are used for safety measures

・Atomized air of the duplex nozzle realizes quick-drying marking
・Sharp marking without scatter
・Changeable marking width (6-20mm)
・Environmental friendly spray
・Air-driven pumps for paint and lubricant are used for safety measures

・Environmental friendly paint(G-series) used for MARKTEC Marking Machines.
・G-series is low toxicity, quick-drying type paint.
・Non-inflammable type paint is also available.

There are various choices available to meet your needs.

Selection example
・ Portable type with excellent portability / operability: IPX6 compatible
・ Automatic ultrasonic inspection system optimized for each part to be inspected

• Equipped with a high-output X-ray tube with a maximum output of 450 kV/15 mA
• Can generate low-noise CT images with fan beam CT
• Achieves high-speed CT imaging with optional cone beam CT
• Enables noiseless imaging even with composite products, such as products made of resin and metal, with a 16-bit line sensor